M.2 Heatsink SSD Cooler for PS5 PCIE NVME or SATA m2 2280 SSD Cooling（Black 2 Pieces）

I just built a new PC workstation, and while I was putting it all together I used these heatsinks for two of my NVMe M.2 drives. And... I was VERY PLEASANTLY SUPRISED by how nice of a kit this is and how well thought-out it is and all that for so little money. Nice job folks! This kit includes a little screwdriver which also has a magnetized tip that makes it much easier to work with the tiny screws, and speaking of the screws it not only includes all the screws you'll need to put the thing together but it also includes two extra screws (one for each heatsink unit) that you can use to latch down the end of the M.2 card to your motherboard because yeah you probably don't have one of those M.2 screws handy do you? Well no worries! And this includes four thermal pads (one for top and one for bottom of each of the two drive kits) which are of different thickness, so read the manual to make sure you use the right thickness thermal pad on the correct side of your M.2 drive - it's easy to visually tell them apart as one size is visually thicker. It also includes a legible and simple manual which was great as other wise I wouldn't have known which thermal pad to apply to the front and which the back. Finally it includes wipes (wet and dry) to clean off your drive if you need it. Such a well thought-out little product. What a value! And it also looks great and WORKS great too - my drive temps have stayed nice and cool.

This kit was easy to use and works well on all of my M.2 ssd. Temps are lower and stable.

Installed on;1. Intel 670p 2TB (chips are only on one side of SSD): fitment was perfect. easy to install.2. Kingston KC3000 2TB (double sided along entire SSD stick): it was a tight fit. If you didn't pinch the SSD & heatsink sandwich together tightly with your fingers, you couldn't start the screws to hold it together. I didn't like pinching it that hard (maybe it won't cause a problem long term), so a day later I took it apart and cut slots in the screw holes on the stamped piece to the outside edge, so instead of a long oval hole, I now had a slot cut to the outside edge. This worked perfectly to fit my KC3000 and I didn't have to pinch it so hard.Great value for the money. I appreciated the thermal pads allowing me to reposition them multiple times without issue. They didn't damage the warranty stickers on the KC3000 when I took it apart and they were re-usable when I put it back together. It would be nice if the oblong screw holes were just a couple mm longer to fit chonkier double sided SSDs without having to pinch them so hard to compress the thermal pads to get the screw hole to line up with the slot enough to start the screw.Overall a good buy and I'm satisfied with my purchase.

This heat sink kit does not work very well for the Samsung 980 Pro SSD. The reason for the poor heat reduction of the 980 Pro SSD is that the chips on the drive are different thickness or heights and the thermal pad and heat sink does not touch all of the chips.This can easily be corrected to make these heat sinks work excellently!First some test information:I have 2 980 Pro 1TB drives in my cool running, perfectly quiet Ryzen 7 Asus TUF 570system.Using the Magician software,Standard Optimization Setting, and monitoring the drive temps with CPUID HWMonitor software.Stock 980 Pro SSD, No Heat sinks, Run a 6 times test, drives reached 150°F +Stock unmodified Heat sinks, Run a 6 times test, drives reached 135°FStock Unmodified Heat sinks with system just being inactive 115° to 117° FModified cut 2 piece Heat sinks, Run a 6 times test, drives reached 120°F max.Modified cut 2 piece Heat sinks, with system just being inactive 102°FWith average use of my computer, I never see it go more than 107°FWhen the drives reached 150°F the report read/write test speeds dropped below 5000.Now with the drives running cool my tested read/write speeds are 7022 and 5169.On with the Modification of the Heat sinks:First Item. The taped screw holes in the aluminum heat sink are very tight.Use a screw with the supplied little screw driver to screw in one of the screws.When the screw becomes tight back the screw out half turn or so and screw it back inuntil it becomes snug again. Back it out and repeat the process until the screw willgo all the way into the heat sink. Do this for all 4 screw holes. This makes final assemblywith the screws go much easier!Now you can follow the description below with the pictures.EDIT: I uploaded the pictures in the proper sequence, but they are not being displayed in the proper order.1.First picture is about screwing the screws into the heat sink to loosen the holes.2.This picture shows the different height of the chips.3.This pictures shows the gaps between the heat sink and the chips.4. Cut the heat sink aluminum in half. Cut 2 pieces of thermal pad.5.Cut the bottom piece with cutters on both sides.6. Bend cut piece several times to snap off piece. Smooth with pliers if needed.7.Put everything together with the thermal pads in place.8.Enjoy a cool running 980 Pro SSD !

Low profile and comes with four thermal pads and two heatsinks. Each comes paired with a bottom plate to take heat away from the top and bottom sections of the NVMe. Both heatsink and plate are securely held by 4 small screws. When secured to the MB, there’s enough clearance in between. Perfect use case for me. The fact that it comes with two sets is a bonus and of great value. Highly recommended!

I primarily bought these for the aesthetics but they do a nice job of keeping things cool as well. I installed the second on my PS5. Both fit well.