Rugged Ridge 1-1303 Bump Stop, Polyurethane, Front; 07-18 Jeep Wrangler Jk/Jku
Details
- BrandRugged Ridge
- Mounting TypeFloor Mount
- MaterialPolyurethane
- ColorRed
- StyleModern
- Finish TypePainted
Description
🚙 Elevate Your Jeep Experience!
- SLEEK AESTHETIC - Painted exterior adds a stylish touch to your rugged ride.
- EASY INSTALLATION - Quick and hassle-free setup to get you back on the road in no time.
- UNMATCHED DURABILITY - Crafted from high-quality polyurethane for long-lasting performance.
- LIMITED 5 YEAR WARRANTY - Peace of mind with a robust warranty backing your purchase.
- PERFECT FIT FOR JEEP ENTHUSIASTS - Designed specifically for 07-18 Jeep Wrangler JK/JKU models.
The Rugged Ridge 1-1303 Bump Stop is a premium polyurethane component designed for the front of 07-18 Jeep Wrangler JK/JKU models. With dimensions of 20.32 x 14.61 x 5.08 cm and a lightweight design of 272 g, this bump stop not only enhances your vehicle's performance but also comes with a limited 5-year warranty for added assurance.
Specifications
| Manufacturer | Rugged Ridge |
| Brand | Rugged Ridge |
| Model | Bump Stop,Front |
| Product Dimensions | 20.32 x 14.61 x 5.08 cm; 272.16 g |
| Item model number | 1-1303 |
| Exterior | Painted |
| Manufacturer Part Number | 1-1303 |
| OEM Part Number | 18368.08 |
| Position | Front |
| Item Weight | 272 g |
Have a Question? See What Others Asked
Reviews
F**Q
Not for offroad
Smashed after one drive only
O**Y
FAKE !!!!
It’s not Rugged Ridge brand , plus it’s so hard to fix , not like the original brands or Rugged Ridge !**** DONT BUY IT !!! ****
J**H
Mejora sustancial en la amortiguación
Muy buena calidad, aunque un poco complicado en su instalación, hay que ejercer bastante presión para que entren, lo cual se logra con unos maderos y un gato hidraulico.
M**O
Good quality and great value.
These are significantly better than the stock bumpstops. However, it's very difficult to put on so be prepared to spend a few hours swearing profusely.After failing at multiple attempts to jack it up with blocks as compression and grease, this is what finally worked for me:Take a 18" 3/8 threaded rod and put it through the bumpstop holder and stops. If you can't find holes in the holder, try cleaning it out, there may be mud/rocks that have collected in there. Place appropriately sized nuts and washers on either end and ratchet into place. This ensures the stops go in straight and is much more controllable.Best of luck.
J**D
Perfect fit, good quality, hard to install unless you know tricks
Perfect fit for my 2012 Jeep Wrangler Sahara Unlimited. They are not easy to install unless you know some tricks. They do not come with install instructions. Basically jack the Jeep up as far as you can to open up the coils. Use a little dish detergent to lube up the coil and push the bump stop in. Next push the bump stop up into place as far as you can by hand. Place a small board below the bump stop in the coil. Lower the Jeep down slowly and the force will push the bump stop up into place.
A**R
Really high quality compared to factory bump stops
The reason the factory bump stops rot and the perch rusts is because they have a tiny center drain hole that gets plugged up allowing water to sit on top of the bumpstop. These are really high quality and have a 1/2" hole in the center that allows them to drain. It was harder to get all of old bump stops out than to replace these. I greased them up and used the wood blocks in the spring method to pop them into place.
M**
Muy buen material
Muy fuertes, para insertarlo la mejor opción es quitar el resorte, insertarlo en diagonal y hacer palanca en el lado faltante, es rápido de esta forma
Common Questions
Trustpilot
4 days ago
2 months ago
